Analisis Pegaruh Desain Kumparan 9-Fasa Simetris Terhadap Daya Keluaran dan Faktor Daya Motor Induksi 3-Fasa

Authors

  • Cayani Dai Putri Institut Teknologi Padang, Indonesia
  • Zuriman Anthony Institut Teknologi Padang, Indonesia
  • Sapannur Bandri Institut Teknologi Padang, Indonesia
  • Sitti Amalia Institut Teknologi Padang, Indonesia
  • Anggun Anugrah Institut Teknologi Padang, Indonesia

DOI:

https://doi.org/10.57235/hemat.v2i1.5012

Keywords:

Motor Induksi 3-Fasa, Desain Kumparan 9-Fasa, Daya Keluaran, Faktor Daya

Abstract

Penelitian ini bertujua untuk menganalisis pengaruh desain kumparan 9-fasa simetris terhadap daya outpu dan faktor daya motor induksi 3-fasa. Motor induksi dipilih dalam penelitian ini dikarenakan strukturnya yang sederhana, serta keandalan dan daya tahannya yang tinggi. Penelitian ini mengembangkan kinerja motor induksi 3-fasa menjadi kumparan 9-fasa dengang harapan dapat meningkatkan kinerja motor induksi tanpa memerlukan sumber tenaga tambahan. Desain kumparan 9-fasa simetris ini  menggunakan gabungan 3 kumparan di setiap slot. Metodologi penelitian ini melibatkan pengujian langsung pada motor induksi di laboratorium dengan memvariasikan beban motor, mengukur arus, kecepatan, faktor daya, tegangan, efisiensi, torsi dan daya keluaran. Hasil dari penelitian ini menunjukan bahwa motor induksi 3-fasa dengan desain kumparan 9-fasa simetris memiliki kinerja yang lebih baik dibandingkan dengan motor induksi 3-fasa konvensional. Penyempurnaan motor induksi 3-fasa dengan desain kumparan 9-fasa disebabkan oleh distribusi medan magnet yang lebih efisien dan padat, sehingga  memungkinkan peningkatan daya output dan faktor daya. Penelitian ini diharapkan dapat memberikan kostribusi bagi pengembangan desain kumparan motor induksi di masa depan.

Downloads

Download data is not yet available.

References

Z. Yang, Q. Ding, X. Sun, J. Ji, and Q. Zhao, “Design and analysis of a novel wound rotor for a bearingless induction motor,” Int. J. Electron., vol. 106, no. 12, pp. 1829–1844, 2019,

Y. Xie, C. Pi, and Z. Li, “Study on design and vibration reduction optimization of high starting torque induction motor,” Energies, vol. 12, no. 7, 2019,

Z. Anthony, S. Bandri, and Y. Warmi, “Analisa Pengaruh Desain 6 Kumparan Simetris pada Motor Induksi 3-fasa terhadap Efisiensi dan Faktor Daya Motor,” Semin. Nas. Ris. Inov. Teknol., vol. 1, no. /51/28

O. AlShorman et al., “Sounds and acoustic emission-based early fault diagnosis of induction motor: A review study,” Adv. Mech. Eng., vol. 13, no. 2,

Z. Anthony and E. Erhaneli, “Disain Baru Bentuk Lilitan Kumparan Motor Induksi 1-fasa Berbasis Bentuk Lilitan Motor Induksi 3-fasa,”

S. Tama and O. Yudha, “No Title,” vol. 4, no. 4, pp. 49–54, 2022.

R. Ni et al., “Efficiency Enhancement of General AC Drive System by Remanufacturing Induction Motor with Interior Permanent-Magnet Rotor,” IEEE Trans. Ind. Electron., vol. 63, no. 2.

W. Fei, P. C. K. Luk, J. Ma, J. X. Shen, and G. Yang, “A high-performance line-start permanent magnet synchronous motor amended from a small industrial three-phase induction motor,” IEEE Trans. Magn., vol. 45, no. 10, pp. 4724–4727, 2009, doi: 10.1109/TMAG.2009.2022179.

D. Y. P. Rambe, Z. Anthony, E. Erhaneli, A. Yuana Dewi, and Z. Zulkarnaeni, “Analisa Pengaruh Desain 6 Fasa dengan Sistem 1 Lapis dan 3 Medan Fluks pada Motor Induksi 3 Fasa Terhadap Torsi dan Kecepatan Motor,” Ranah Res. J. Multidiscip. Res. Dev., vol. 5, no. 2, pp. 140–149, 2023, doi: 10.38035/rrj.v5i2.744.

N. R. Garcia, M. J. Duran, and I. G. Prieto, “A Simple , Fast and Robust Open-phase Fault,” no. April, 2017.

A. S. Abdel-khalik, S. Member, A. M. Massoud, and S. Member, “Nine-Phase Six-Terminal Induction Machine Modelling using Vector Space Decomposition,” no. April, 2018, doi: 10.1109/TIE.2018.2833041.

I. Gonzalez-prieto, I. Zoric, M. J. Duran, and E. Levi, “Constrained Model Predictive Control in Nine- phase Induction Motor Drives,” 2019.

A. S. Abdel-khalik, S. Member, A. M. Massoud, S. Member, S. Ahmed, and S. Member, “Nine-Phase Six-Terminal Induction Machine Modelling using Vector Space Decomposition,” vol. 0046, no. c, 2018, doi: 10.1109/TIE.2018.2833041.

I. S. De Freitas, M. L. Quirino, and F. Salvadori, “Twelve-Phase Induction Machine Analysis With Harmonic Injection,” pp. 1611–1618, 2018.

S. M. Dabour, A. S. Abdel-khalik, S. Ahmed, and A. M. Massoud, “A New Dual Series-Connected Nine-Switch Converter Topology for a Twelve-Phase Induction Machine Wind Energy System,” pp. 139–144, 2016.

G. Rezazadeh et al., “Analysis of Six-Phase Induction Motor with Distributed and Concentrated Windings by Using the Winding Function Method,” 2018 XIII Int. Conf. Electr. Mach., pp. 2423–2429, 2018, doi: 10.1109/ICELMACH.2018.8507049.

Z. Anthony, S. Bandri, E. Erhaneli, Y. Warmi, Z. Zulkarnaini, and F. Firdaus, “A Simple Way To Increase the Performance of the 3-Phase Induction Motor,” J. Pharm. Negat. Results, vol. 13, no. 7, pp. 4975–4983, 2022, doi: 10.47750/pnr.2022.13.S07.615.

N. Evalina, A. H. Azis, and Zulfikar, “Pengaturan Kecepatan Putaran Motor Induksi 3 Fasa Menggunakan Programmable logic controller,” J. Electr. Technol., vol. 3, no. 2, pp. 73–80, 2018.

Y. Demir, S. Member, and M. Aydin, “A Novel Asymmetric and Unconventional Stator Winding Configuration and Placement for Dual Three-Phase Surface PM Motor,” vol. 9464, no. c, pp. 1–5, 2017, doi: 10.1109/TMAG.2017.2710424.

M. A. Kabir and I. Husain, “Design of synchronous reluctance motor with multilayer AC winding,” 2017 IEEE Int. Electr. Mach. Drives Conf. IEMDC 2017, 2017, doi: 10.1109/IEMDC.2017.8002131.

Z. Anthony, “Disain Baru Bentuk Lilitan Kumparan Motor Induksi 1-fasa Berbasis Bentuk Lilitan Motor Induksi 3-fasa,” pp. 245–249, 2017, doi: 10.21063/PIMIMD4.2017.245-249.

M. Karpe, S. Ghosh, N. Shindhe, R. Birajdar, and D. Bhave, “Optimization of Single-Phase Induction Motor,” CENCON 2019 - 2019 IEEE Conf. Energy Convers., vol. 2019-January, pp. 115–120, 2019, doi: 10.1109/CENCON47160.2019.8974827.

N. Riviere, M. Villani, and M. Popescu, “Optimisation of a High Speed Copper Rotor Induction Motor for a Traction Application,” IECON Proc. (Industrial Electron. Conf., vol. 2019-October, pp. 2720–2725, 2019, doi: 10.1109/IECON.2019.8927627.

Z. Anthony, E. Erhaneli, and B. Busran, “A new equivalent circuit of the three-phase induction motor (case studies: Current and power factor of the motor),” ARPN J. Eng. Appl. Sci., vol. 12, no. 23, pp. 6967–6974, 2017.

J. Editorial Team, “Editorial Team,” J. Vocat. Nurs., vol. 1, no. 1, 2020, doi: 10.20473/jovin.v1i1.19873.

Z. Anthony, “Studi Pengaruh Perubahan Frekwensi Sumber terhadap Faktor Daya Motor Induksi 3-Fasa,” Tek. Elektro Itp, vol. 2, no. 2, pp. 49–52, 2013.

A. Shawier, M. S. Abdel-majeed, and W. E. Abdel-azim, “Effect of Winding Design on the Performance of Predictive Current Control of Six-Phase Induction Machine-Based Propulsion Systems,” IEEE Access, vol. 10, no. August, pp. 80587–80599, 2022, doi: 10.1109/ACCESS.2022.3194893.

Downloads

Published

2025-01-29

How to Cite

Putri, C. D., Anthony, Z., Bandri, S., Amalia, S., & Anugrah, A. (2025). Analisis Pegaruh Desain Kumparan 9-Fasa Simetris Terhadap Daya Keluaran dan Faktor Daya Motor Induksi 3-Fasa. Journal of Humanities Education Management Accounting and Transportation, 2(1), 264–272. https://doi.org/10.57235/hemat.v2i1.5012

Issue

Vol. 2 No. 1 (2025): Februari 2025

Section

Articles

Citation Check

License

  1. Authors certify that the work reported here has not been published before and contains no materials the publication of which would violate any copyright or other personal or proprietary right of any person or entity.
  2. Authors dont transfer or license the copyright of publishing to HEMAT: Journal of Humanities Education Management Accounting and Transportation Research to publish the article in any media format, to share, to disseminate, to index, and to maximize the impact of the article in any databases.
  3. Authors hereby dont agree to transfer a copyright for publishing to HEMAT: Journal of Humanities Education Management Accounting and Transportation a Publisher of the manuscript. 
  4. Authors reserve the following: 
    1. all proprietary rights other than copyright such as patent rights; 
    2. the right to use all or part of this article in future works of our own such as in books and lectures;
    3. use for presentation in a meeting or conference and distributing copies to attendees; 
    4. use for internal training by author's company;
    5. distribution to colleagues for their research use;
    6. use in a subsequent compilation of the author's works;
    7. inclusion in a thesis or dissertation;
    8. reuse of portions or extracts from the article in other works (with full acknowledgement of final article);
    9. preparation of derivative works (other than commercial purposes) (with full acknowledgement of final article); and
    10. voluntary posting on open web sites operated by author or author’s institution for scholarly purposes, but it should follow the open access license of Creative Common CC BY-NC License.